Overview
The Perle S-10GT-XFPH Media Converter transparently connects 10GBase-T Ethernet links over multimode or single mode fiber. Each 10GbE Media Converter comes with one RJ45 10GBase-T port and an empty slot for one XFP module.
Copper to Fiber conversion is achieved by inserting an XFP fiber transceiver that supports multimode and single-mode fiber, including CWDM/DWDM wavelengths. Copper to copper is achieved by inserting XFP 10Gbase-CX4 transceivers.
The empty transceiver port on the S-10GT-XFPH Media Converter allows for flexible network configurations to meet any requirement using a variety of MSA compliant XFPs. You can use this product to convert:
- 10GBase-T (RJ45) to XFP
- 10GBase-T (RJ45) to 10GBase-CX4 (XFP)
Perle 10 Gigabit Ethernet to Fiber Converters provide an economical path to extend the distance of an existing 10GbE link. Network Administrators can “see-everything” with Perle’s advanced features such as Smart Link Pass-Through, Fiber Fault Alert, a built-in Link Test capability and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make the Perle S-10GT-XFPH Media Converter the smart choice for IT professionals. This product is also available for managed networks with AAA Security.
S-10GT-XFPH Media Converter Features
| Smart Link Pass-Through | When Smart Link Pass-Through is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.
When Smart Link Pass-Through is disabled, if a link loss is detected on one port the transmit signal remains enabled on the other port. |
| Fiber Fault Alert | With Fiber Fault Alert the state of the 10 Gigabit Ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G Ethernet interface of the media converter. |
| Green Ethernet | Utilizes Green Ethernet energy saving technology based on industry standards such as:
|
| Built-in Link Test | When enabled, the built-in packet generator transmits Ethernet test frames to its 10 Gigabit Ethernet peer. The remote media converter will auto-detect the test frames and loopback the test frames. Any frames received in error, will cause the Power, LK1 and LK2 LEDs to illuminate in a specific combination to identify the error. During the test different bit test patterns will be utilized every 5 seconds ensuring a thorough link test. |
| Test Mode Auto-detect | No switches are required to be flipped in order to go into test mode. The remote media converter will enter test mode automatically when requested by its central site peer. This virtually eliminates unnecessary truck rolls to a remote site when diagnosing a link failure. |
| EDC Mode Control | Electronic Dispersion Compensation (EDC) is an algorithmic method used to compensate for optical dispersion that occurs on high speed 10 Gigabit links. EDC mode settings are automatically configured by the media converter based on the information retrieved from the XFP module. This will enable proper operation for extended multimode 10GBase-LRM as well as active or passive copper cabling. |
| Module Temperature Protection | Protects your DOM/DMI capable XFP module by monitoring its internal temperature and will automatically shut down the XFP if the module is operating above its maximum temperature threshold. |
| High Power Level 4 XFPs | High powered Level 4 XFPs are supported. |
| Jumbo Packets | Transparent to Jumbo Frames with a maximum MTU size of 10,024 bytes |
| VLAN | Transparent to VLAN tagged packets. |
| Power Strain Relief strap | A strain relief strap is provided to ensure a solid and secure power connection to the media converter. Ideal for areas that may be exposed to any vibration. |
| Remote Loopback | Capable of performing a loopback on the 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link. |
Hardware Specs
| Power | S-10GT-XFPH | |
|---|---|---|
| Input Supply Voltage | 9 – 30 vDC, unregulated ( 12 vDC Nominal ) | |
| Maximum Power Consumption (watts) | 15* | |
| Power Connector | 5.5mm x 9.5mm x 2.1mm barrel socket | |
| Power Adapter | ||
| Universal AC/DC Adapter | 100-240v AC, regulated AC/12v DC adapter included | |
| Indicators | ||
| Power / TST |
|
|
| LK1 (SFP/XFP) |
|
|
| LK2 |
|
|
| Switches – accessible through a side opening in the chassis | ||
| Link Mode | When the Link Mode switch is enabled (default), each port will reflect the state of its port peer using Smart Link Pass-Through. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.
When the switch is in the down position, Smart Link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port. |
|
| Fiber Fault Alert |
Enabled (Default – Up) With Fiber Fault Alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter Disabled (Down) |
|
| Test Mode | Through the use of three dip switches the unit, and its peer, can be placed into a link test mode which will verify the integrity of the link through the use of its built-in link test generator. The unit can also be placed into a simple line loopback. | |
| EEE Green Ethernet | When enabled (default), the media converter will operate as an IEEE 802.3az Energy Efficient Ethernet (EEE) compliant device. | |
| Loopback | Capable of performing a loopback on the 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link. | |
| Connectors | S-10GT-XFPH | |
| 10GBase-T (RJ45) | IEEE 802.3an 100 meters on CAT6A or better |
|
| Pluggable 10G Fiber Transceiver slot ( Hot insertion and removable) | 10 Gigabit XFP Slot
|
|
| Voltages supplied to XFP slots | 1.8V, 3.3V, 5V and -5.2V | |
| Supported 10 Gigabit Fiber pluggable transceivers | IEEE 802.3ae compliant:
CWDM/DWDM |
|
| Supported 10 Gigabit Copper pluggable transceivers | IEEE 802.3ak compliant:
|
|
| Environmental Specifications | S-10GT-XFPH | |
| Operating Temperature | 0° C to 50° C (32° F to 122° F) | |
| Storage Temperature | minimum range of -25° C to 70° C (-13° F to 158° F) | |
| Operating Humidity | 5% to 90% non-condensing | |
| Storage Humidity | 5% to 95% non-condensing | |
| Operating Altitude | Up to 3,048 meters (10,000 feet) | |
| Heat Output ( BTU/HR ) |
51 | |
| MTBF (Hours)** |
Without power adaptor: 284,367 With power adaptor: 190,260 |
|
| Chassis | Metal with an IP20 ingress protection rating | |
| Mounting | ||
| Din Rail Kit | Optional | |
| Wall / Rack Mount Kit | Optional | |
| Product Weight and Dimensions | S-10GT-XFPH | |
| Product Weight | 0.38 kg, 0.84 lbs | |
| Product Dimensions | 8 x 12 x 4.2 cm (3.1 x 4.7 x 1.7 inches) | |
| Shipping Weight | 0.93 kg, 2.1 lbs | |
| Shipping Dimensions | 26 x 17 x 7 cm (10.2 x 6.7 x 2.8 inches) | |
| Regulatory Approvals | ||
| Emissions | FCC Part 15 Class A, EN55022 Class A | |
| CISPR 22 Class A CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
||
| EN61000-3-2 | ||
| Immunity | EN55024 | |
| Electrical Safety | UL 60950-1 | |
| IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
||
| CE | ||
| Environmental | Reach, RoHS and WEEE Compliant | |
| Other | ECCN: 5A991 | |
| HTSUS Number: 8517.62.0050 | ||
| Perle Limited Lifetime Warranty | ||
*Maximum rating for both media converter and modules inserted. Actual rating is dependent on the power consumption of the XFP modules inserted.
**Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Application Diagrams
| 10 Gigabit Copper to Fiber Media Conversion |
|---|
|
Convert one 10G Ethernet media to another   |