When you need to extend Ethernet services beyond the general IEEE 802.3 limits of 100m / 328ft, and new fiber cabling is cost prohibitive, the eR-S1110 Ethernet Repeater is the perfect solution. Transparently extend 10/100/1000 Ethernet connections across twisted pair ( CAT5/6/7 ) to extend your network reach an additional 100m (328ft).
This simple and effective point to point Ethernet Repeater and Rate Converter is perfect for commercial buildings, residential units, hospitality environments or for connecting a remote office or private-network backbone to a corporate LAN. Use it anywhere you need Ethernet communication links between separated LANs or LAN devices (i.e. PCs, digital sensors, VoIP phones, WiFi APs, IP cameras and more).
The eR-S1110 Repeater can also operate as a Powered Device (PD) under IEEE 802.3af supporting end-span and mid-span power sources (PSE). This makes it ideal for organizations that need to deploy equipment in locations that are difficult or too costly to have separate AC power installed such as ceilings, walls and kiosks.
Perle’s advanced features such as Link Pass-Through, Interlink Fault Feedback, and Loopback allow network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Repeaters the smart choice for IT professionals.
eR-S1110 Ethernet Repeater Features
Extend Ethernet over twisted pair
Extend an Ethernet link over category 5e, 6 and 7 cabling up to an additional 100m / 328ft
The eR-S1110 can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different.
Plug and Play operation
Perle Ethernet Repeaters will automatically configure your Ethernet connection. Once a connection is made, both ends will automatically adjust relevant Ethernet parameters to establish connection.
Ethernet Link Pass-Through
With Link Pass-Through the state of the 10/100/1000Base-T Ethernet connection is “passed through” the Ethernet link to the 10/100/1000Base-T Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.
Competitive Ethernet repeaters without this feature will never detect or report any error conditions.
The Ethernet Repeater supports auto negotiation on the 10/100/1000Base-T interface.
Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
|Jumbo Packets||Transparent to Jumbo Frames with a maximum MTU size of 10,024 bytes|
Transparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocols
Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strap
A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Repeater. Ideal for areas that may be exposed to vibration.
|Port||2 ports RJ45 – 10/100/1000 Base-T – Shielded|
|Auto-MDIX||Auto-MDIX enables proper operation with either straight-through or crossover cabling|
|Distance||Distance up to 100 meters (328 feet) as per IEEE 802.3|
|Maximum Frame Size||10240 bytes|
|Input Supply Voltage||9 – 30 vDC, unregulated (12 vDC Nominal)|
|POE||As per 802.3af PD specifications (Port #1).
PD ( Class 0 or 4 device )
|Power Consumption||2.2 watts|
|Power Connectors||5.5mm x 9.5mm x 2.1mm barrel socket|
|Back of product|
|Universal AC/DC adapter||100-240v AC, regulated 12V DC adapter included|
|Power||This green LED is turned on when power is applied to the Ethernet Repeater. Otherwise it is off. The LED will blink when Hardware Fault.|
|ETH||Indicates link status and activity on Ethernet port(s).
|Link Mode||Standard (Default)– The 10/100/1000 Base-T link remains active independent of the state of the Ethernet link on its remote peer.|
|Link Pass-Through – the state of the 10/100/1000 Base-T Ethernet connection is “passed through” or propagated to the 10/100/1000 Base-T Ethernet link on its remote Ethernet Repeater peer. This enables a managed switch to report the state of the remote device to its network management system.|
|Operating Temperature||-10 C to 50 C (14 F to 122 F)|
|Storage Temperature||-25 C to 70 C (-13 F to 158 F)|
|Operating Humidity||5% to 90% non-condensing|
|Storage Humidity||5% to 95% non-condensing|
|Operating Altitude||Up to 3,048 meters (10,000 feet)|
|Heat Output ( BTU/HR )||7.5|
|MTBF (Hours)*||Without power adaptor: 613,826|
|Wall or Panel||Included|
|Din Rail Kit||Optional|
|Product Weight and Dimensions|
|Weight||0.23 kg / 0.51 lbs|
|Dimensions||90 x 64 x 22 mm / 3.54 x 2.52 0.87 inches|
|Shipping Weight||0.45 kg / 1 lbs|
|Shipping Dimensions||260 x 170 x 70 mm / 10 x 6.7 x 2.76 inches|
|Emissions||FCC 47 Part 15 Class A
EN6100-4-2 (ESD): Contact
EN 61000-4-8 (PFMF)
|Electrical Safety||UL/ULC/EN 62368-1|
|Environmental||Reach, RoHS and WEEE Compliant|
|HTSUS Number: 8517.62.0050|
|Perle Lifetime warranty|
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
|Extend 10/100/1000 Ethernet across Twisted Pair Wire|
|Extend an Ethernet link up to 200 meters ( 656 feet ) using an Ethernet Repeater
|Extend 10/100/1000 Ethernet across Twisted Pair Wire with PoE|
|Extend an Ethernet link up to 200 meters ( 656 feet ) using a PoE Ethernet Repeater
|Cascading Ethernet Repeaters|
|Extend an Ethernet link up to 300 meters ( 984 feet ). There is no limit to the number of repeaters that can be cascaded.
Using a PoE Switch and a PoE Injector
Using two PoE Injectors
Using one PoE Injector